Welcome to the Kurt J. Lesker Company.  

Sign In | Register

Current Region: International (Change) | Contact Us |   RSS   Twitter   LinkedIn   YouTube

Close

Please select your country or region to be
directed to the appropriate Lesker site.

Carbon (Pyrolytic Graphite) (C) Sputtering Targets

Overview

Our comprehensive offering of sputtering targets, evaporation sources and other deposition materials is listed by material throughout the website. Below you will find budgetary pricing for sputtering targets and deposition materials per your requirements. Actual prices may vary due to market fluctuations. Contact international@lesker.com for current pricing or for a quote on sputtering targets and other deposition products not listed.


Specifications

Material TypeCarbon
SymbolC
Atomic Weight12.0107
Atomic Number6
Color/AppearanceBlack, Non-Metallic
Thermal Conductivity140 W/m.K
Melting Point (°C)~3,652
Coefficient of Thermal Expansion7.1 x 10-6/K
Theoretical Density (g/cc)2.25
Z Ratio3.26
SputterPDC
Max Power Density*
(Watts/Square Inch)
80
Type of BondIndium, Elastomer
CommentsE-beam preferred. Arc evaporation. Poor film adhesion.

* This is a recommendation based on our experience running these materials in KJLC guns. The ratings are based on unbonded targets and are material specific. Bonded targets should be run at lower powers to prevent bonding failures. Bonded targets should be run at 20 Watts/Square Inch or lower, depending on the material.


Z-Factors

Empirical Determination of Z-Factor

Unfortunately, Z Factor and Shear Modulus are not readily available for many materials. In this case, the Z-Factor can also be determined empirically using the following method:

  • Deposit material until Crystal Life is near 50%, or near the end of life, whichever is sooner.
  • Place a new substrate adjacent to the used quartz sensor.
  • Set QCM Density to the calibrated value; Tooling to 100%
  • Zero thickness
  • Deposit approximately 1000 to 5000 A of material on the substrate.
  • Use a profilometer or interferometer to measure the actual substrate film thickness.
  • Adjust the Z Factor of the instrument until the correct thickness reading is shown.

Another alternative is to change crystals frequently and ignore the error. The graph below shows the % Error in Rate/Thickness from using the wrong Z Factor. For a crystal with 90% life, the error is negligible for even large errors in the programmed versus actual Z Factor.


Material Notes

NOTE: Bonding is recommended for these materials. Many materials have characteristics which are not amenable to sputtering, such as, brittleness and low thermal conductivity. Request more information, please click here.

SDS
Click here for the Carbon (Pyrolytic Graphite) SDS.
Request A Quote
Can't find the size or material you need? Please use our Materials Quotation Form to request.
Deposition Materials FAQ
Click here for answers to some of the most common questions we get asked.
Contact Us
To speak with someone directly, please call 1-412-387-9200 or email international@lesker.com.

Ordering Table

Material Size Purity Compatible Guns Part # Price Add To
Cart
Material Size Purity Compatible Guns Part # Price Add To
Cart
Carbon (Pyrolytic Graphite) 1.00" Dia. x 0.125" Thick 99.999% All Standard Guns EJTPYRO501A2 $175.00
Carbon (Pyrolytic Graphite) 1.00" Dia. x 0.250" Thick 99.999% All Standard Guns EJTPYRO501A4 $195.00
Carbon (Pyrolytic Graphite) 2.00" Dia. x 0.125" Thick 99.999% All Standard Guns EJTPYRO502A2 $300.00
Carbon (Pyrolytic Graphite) 2.00" Dia. x 0.250" Thick 99.999% All Standard Guns EJTPYRO502A4 $499.00
Carbon (Pyrolytic Graphite) 3.00" Dia. x 0.125" Thick 99.999% All Standard Guns EJTPYRO503A2 $345.00
Carbon (Pyrolytic Graphite) 3.00" Dia. x 0.250" Thick 99.999% All Standard Guns EJTPYRO503A4 $495.00
Carbon (Pyrolytic Graphite) 4.00" Dia. x 0.125" Thick 99.999% All Standard Guns EJTPYRO504A2 P.O.R.
Carbon (Pyrolytic Graphite) 4.00" Dia. x 0.250" Thick 99.999% All Standard Guns EJTPYRO504A4 P.O.R.

Bonded Assemblies Ordering Table

Material Target
Size
Purity Bonding Type Backing Plate
Size
Compatible Guns PartNo Price Add To
Cart
Material Target
Size
Purity Bonding Type Backing Plate
Size
Compatible Guns PartNo Price Add To
Cart
Carbon (Pyrolytic Graphite) 2.00" Dia x 0.125" Thick 99.999% Indium 2.00" Dia x 0.125" Thick All Standard Guns EJUPYRO502A4 P.O.R.
Carbon (Pyrolytic Graphite) 3.00" Dia x 0.125" Thick 99.999% Indium 3.00" Dia x 0.125" Thick All Standard Guns EJUPYRO503A4 P.O.R.
Carbon (Pyrolytic Graphite) 3.00" Dia x 0.125" Thick 99.999% Indium 3.00" Dia x 0.092" Thick Standard TORUS 3 EJUPYRO503T4 P.O.R.

Notes: Bonded assemblies to be used in TORUS Mag Keeper guns require Elastomer bonding

 

Kurt J Lesker Company Logo

Buy Online or Call
+1 412 387 9200

ISO:9001 The Kurt J. Lesker Company is an ISO:9001 certified company. Copyright ©1996-2017 Kurt J. Lesker Company® All rights reserved.