Welcome to the Kurt J. Lesker Company.  

Sign In | Register

Current Region: International (Change) | Contact Us |   RSS   Twitter   LinkedIn   YouTube

Close

Please select your country or region to be
directed to the appropriate Lesker site.

Erbium Oxide (Er2O3) Sputtering Targets

Overview

Our comprehensive offering of sputtering targets, evaporation sources and other deposition materials is listed by material throughout the website. Below you will find budgetary pricing for sputtering targets and deposition materials per your requirements. Actual prices may vary due to market fluctuations. Contact international@lesker.com for current pricing or for a quote on sputtering targets and other deposition products not listed.


Specifications

Material TypeErbium Oxide
SymbolEr2O3
Color/AppearancePink, Solid
Melting Point (°C)2,350
Theoretical Density (g/cc)8.64
Z Ratio**1.00
SputterRF, RF-R
Type of BondIndium, Elastomer
CommentsLoses oxygen.

** The z-ratio is unknown. Therefore, we recommend using 1.00 or an experimentally determined value. Please click here for instructions on how to determine this value.

Z-Factors

Empirical Determination of Z-Factor

Unfortunately, Z Factor and Shear Modulus are not readily available for many materials. In this case, the Z-Factor can also be determined empirically using the following method:

  • Deposit material until Crystal Life is near 50%, or near the end of life, whichever is sooner.
  • Place a new substrate adjacent to the used quartz sensor.
  • Set QCM Density to the calibrated value; Tooling to 100%
  • Zero thickness
  • Deposit approximately 1000 to 5000 A of material on the substrate.
  • Use a profilometer or interferometer to measure the actual substrate film thickness.
  • Adjust the Z Factor of the instrument until the correct thickness reading is shown.

Another alternative is to change crystals frequently and ignore the error. The graph below shows the % Error in Rate/Thickness from using the wrong Z Factor. For a crystal with 90% life, the error is negligible for even large errors in the programmed versus actual Z Factor.


Material Notes

NOTE:

  • Bonding is recommended for these materials. Many materials have characteristics which are not amenable to sputtering, such as, brittleness and low thermal conductivity. Request more information, please click here.
  • This material may require special ramp up and ramp down procedures. This process may not be necessary with other materials. Targets that have a low thermal conductivity are susceptible to thermal shock. Please click here for Ramp Procedure for Ceramic Target Break-in.

SDS
Click here for the Erbium Oxide SDS.
Request A Quote
Can't find the size or material you need? Please use our Materials Quotation Form to request.
Deposition Materials FAQ
Click here for answers to some of the most common questions we get asked.
Contact Us
To speak with someone directly, please call 1-412-387-9200 or email international@lesker.com.

Ordering Table

Material Size Purity Compatible Guns Part # Price Add To
Cart
Material Size Purity Compatible Guns Part # Price Add To
Cart
Clearance Item Erbium Oxide 1.00" Dia. X 0.125" Thick 99.99% All Standard Guns EJTEROX401A2 P.O.R.
Clearance Item Erbium Oxide 1.00" Dia. X 0.250" Thick 99.99% All Standard Guns EJTEROX401A4 P.O.R.
Erbium Oxide 2.00" Dia. X 0.125" Thick 99.99% All Standard Guns EJTEROX402A2 P.O.R.
Clearance Item Erbium Oxide 2.00" Dia. X 0.250" Thick 99.99% All Standard Guns EJTEROX402A4 P.O.R.
Erbium Oxide 3.00" Dia. X 0.125" Thick 99.99% All Standard Guns EJTEROX403A2 P.O.R.
Erbium Oxide 3.00" Dia. X 0.250" Thick 99.99% All Standard Guns EJTEROX403A4 P.O.R.
Erbium Oxide 4.00" Dia. X 0.125" Thick 99.99% All Standard Guns EJTEROX404A2 P.O.R.
Erbium Oxide 4.00" Dia. X 0.250" Thick 99.99% All Standard Guns EJTEROX404A4 P.O.R.
Note Clearance Item = Limited availability and specially priced.

 

Kurt J Lesker Company Logo

Buy Online or Call
+1 412 387 9200

ISO:9001 The Kurt J. Lesker Company is an ISO:9001 certified company. Copyright ©1996-2017 Kurt J. Lesker Company® All rights reserved.