Welcome to the Kurt J. Lesker Company.  

Sign In | Register

Current Region: International (Change) | Contact Us |   RSS   Twitter   LinkedIn   YouTube

Close

Please select your country or region to be
directed to the appropriate Lesker site.

Zinc (Zn) Sputtering Targets

Overview

Our comprehensive offering of sputtering targets, evaporation sources and other deposition materials is listed by material throughout the website. Below you will find budgetary pricing for sputtering targets and deposition materials per your requirements. Actual prices may vary due to market fluctuations. Contact international@lesker.com for current pricing or for a quote on sputtering targets and other deposition products not listed.


Specifications

Material TypeZinc
SymbolZn
Atomic Weight65.38
Atomic Number30
Color/AppearanceBluish Pale Gray, Metallic
Thermal Conductivity116 W/m.K
Melting Point (°C)420
Coefficient of Thermal Expansion30.2 x 10-6/K
Theoretical Density (g/cc)7.14
Z Ratio0.514
SputterDC
Max Power Density*
(Watts/Square Inch)
50
Type of BondIndium, Elastomer
CommentsEvaporates well under wide range of conditions.

* This is a recommendation based on our experience running these materials in KJLC guns. The ratings are based on unbonded targets and are material specific. Bonded targets should be run at lower powers to prevent bonding failures. Bonded targets should be run at 20 Watts/Square Inch or lower, depending on the material.


Z-Factors

Empirical Determination of Z-Factor

Unfortunately, Z Factor and Shear Modulus are not readily available for many materials. In this case, the Z-Factor can also be determined empirically using the following method:

  • Deposit material until Crystal Life is near 50%, or near the end of life, whichever is sooner.
  • Place a new substrate adjacent to the used quartz sensor.
  • Set QCM Density to the calibrated value; Tooling to 100%
  • Zero thickness
  • Deposit approximately 1000 to 5000 A of material on the substrate.
  • Use a profilometer or interferometer to measure the actual substrate film thickness.
  • Adjust the Z Factor of the instrument until the correct thickness reading is shown.

Another alternative is to change crystals frequently and ignore the error. The graph below shows the % Error in Rate/Thickness from using the wrong Z Factor. For a crystal with 90% life, the error is negligible for even large errors in the programmed versus actual Z Factor.


SDS
Click here for the Zinc SDS.
Request A Quote
Can't find the size or material you need? Please use our Materials Quotation Form to request.
Deposition Materials FAQ
Click here for answers to some of the most common questions we get asked.
Contact Us
To speak with someone directly, please call 1-412-387-9200 or email international@lesker.com.

Ordering Table

Material Size Purity Compatible Guns Part # Price Add To
Cart
Material Size Purity Compatible Guns Part # Price Add To
Cart
Zinc 1.00" Dia. x 0.125" Thick 99.99% All Standard Guns EJTZNXX401A2 $80.00
Zinc 1.00" Dia. x 0.125" Thick 99.995% All Standard Guns EJTZNXX451A2 $101.00
Zinc 1.00" Dia. x 0.250" Thick 99.99% All Standard Guns EJTZNXX401A4 $85.00
Zinc 1.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX451A4 $116.00
Zinc 2.00" Dia. x 0.125" Thick 99.99% All Standard Guns EJTZNXX402A2 $96.00
Zinc 2.00" Dia. x 0.125" Thick 99.995% All Standard Guns EJTZNXX452A2 $125.00
Zinc 2.00" Dia. x 0.250" Thick 99.99% All Standard Guns EJTZNXX402A4 $108.00
Zinc 2.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX452A4 $158.00
Zinc 3.00" Dia. x 0.125" Thick 99.99% All Standard Guns EJTZNXX403A2 $172.00
Zinc 3.00" Dia. x 0.125" Thick 99.995% All Standard Guns EJTZNXX453A2 $180.00
Zinc 3.00" Dia. x 0.250" Thick 99.99% All Standard Guns EJTZNXX403A4 $180.00
Zinc 3.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX453A4 $185.00
Zinc 4.00" Dia. x 0.125" Thick 99.99% All Standard Guns EJTZNXX404A2 $185.00
Zinc 4.00" Dia. x 0.125" Thick 99.995% All Standard Guns EJTZNXX454A2 $190.00
Zinc 4.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX454A4 P.O.R.
Zinc 6.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX456A4 P.O.R.
Zinc 8.00" Dia. x 0.250" Thick 99.995% All Standard Guns EJTZNXX458A4 P.O.R.

Bonded Assemblies Ordering Table

Material Target
Size
Purity Bonding Type Backing Plate
Size
Compatible Guns PartNo Price Add To
Cart
Material Target
Size
Purity Bonding Type Backing Plate
Size
Compatible Guns PartNo Price Add To
Cart
Zinc 1.00" Dia x 0.125" Thick 99.99% Indium 1.00" Dia x 0.125" Thick All Standard Guns EJUZNXX401A4 P.O.R.
Zinc 2.00" Dia x 0.125" Thick 99.99% Indium 2.00" Dia x 0.125" Thick All Standard Guns EJUZNXX402A4 P.O.R.
Zinc 1.00" Dia x 0.125" Thick 99.995% Indium 1.00" Dia x 0.125" Thick All Standard Guns EJUZNXX451A4 P.O.R.
Zinc 2.00" Dia x 0.125" Thick 99.995% Indium 2.00" Dia x 0.125" Thick All Standard Guns EJUZNXX452A4 P.O.R.
Zinc 4.00" Dia x 0.125" Thick 99.995% Indium 4.00" Dia x 0.125" Thick All Standard Guns EJUZNXX454A4 P.O.R.

Notes: Bonded assemblies to be used in TORUS Mag Keeper guns require Elastomer bonding

 

Kurt J Lesker Company Logo

Buy Online or Call
+1 412 387 9200

ISO:9001 The Kurt J. Lesker Company is an ISO:9001 certified company. Copyright ©1996-2017 Kurt J. Lesker Company® All rights reserved.